DAB Wet rotor circulator BWO 155 R ZM code 433121010
- Circulation pump for closed and pressurized or open vessel domestic hot water systems.
- Single brass body, spherical steel impeller, wet rotor motor.
- Version with pump body
- with R ½” thread (R version) in which the valves (non-return and shut-off) must be installed separately
APPLICATIONS
A distinction is made between two types of systems:
- Single circuit system:
VORTEX domestic hot water pumps are suitable for installation in single houses or condominiums, depending on the route of the pipes.
- Branched plant:
VORTEX domestic hot water pumps can be used in condominiums with a maximum of 12 apartments after installing additional VORTEX circulation regulators with automatic compensation on the lines.
For VORTEX, energy saving and user comfort are priorities.
The VORTEX regulation components and accessories allow you to comply with the regulations on heating systems relating to the automatic activation and exclusion of the domestic hot water pump and the limitation of the hot water temperature
CONSTRUCTION FEATURES OF THE ENGINE
The magnetic field produced in the motor acts directly on the magnetic rotor. The hydraulic part is hermetically separated from the electrical part.
The spherical rotor motor requires only a sealing ring between the motor and the pump body.
It is protected against short circuits and therefore does not require a motor protector. The rotor can be easily cleaned or replaced.
- long duration
- without shaft, without bearings
- low power consumption (25 W)
- silent operation
- minimal risk of limescale deposits
- Fixing ring
The ring nut allows you to quickly separate the motor from the pump body, thus facilitating cleaning and removing limescale from the parts in contact with water.
CONSTRUCTION FEATURES OF THE PUMP
Pump body with R 1/2” thread
- internal thread
- on request also with press fitting set 1/2“ external x Ø 15 internal
Non-return valve and ball shut-off valve
Correct operation of the system is guaranteed only with a non-return valve in tune with the pump. For pumps with body with R 1/2“ thread, the non-return valve and the ball shut-off valve must be installed separately.
GENERAL | |
---|---|
Model | BWO 155 R BWO 155 R ZM |
Code | 433121010 |
Wheelbase | 80 mm |
Pump connections | ½” |
Versions | mechanical timer |
Operation range | up to 640 l/h with head up to 1.25 metres |
Maximum liquid temperature | +95°C |
Operating pressure | 10 bar (1000 kPa) |
Absorbed power | 2.5-9W |
Circulator protection degree | IP 44 |
ELECTRICAL DATA | |
---|---|
Phase | Single phase |
Diet | 230V 50Hz |
HYDRAULIC DATA | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Q=m3h | 0 | 0.05 | 0.1 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.7 | 0.8 | 0.9 |
Q=l/min | 0 | 0.85 | 1.70 | 3.35 | 5 | 6.70 | 8.35 | 10 | 11.70 | 1.35pm | 15 |
H (m) | 1.4 | 1.3 | 1.25 | 1.1 | 1 | 0.9 | 0.75 | 0.6 | 0.4 | 0.25 | 0.1 |
Free Shipping Over:
-
149€ 🇮🇹
-
249€ 🇩🇪 🇦🇹
-
299€ 🇧🇪 🇫🇷 🇱🇺 🇳🇱 🇵🇱 🇨🇿
-
349€ 🇩🇰 🇵🇹 🇸🇰 🇪🇸 🇭🇺
-
399€ 🇧🇬 🇭🇷 🇪🇪 🇮🇪 🇱🇻 🇱🇹 🇷🇴 🇸🇮 🇸🇪
-
999£ 🇬🇧 🇨🇭 customs duties included